$1.20

Winter Postmark Christmas Ornament SVG

0 reviews
  • Subtotal

    {{ currencyFormat( pricing_summary.total_amount ) }}

A Christmas ornament with a postal theme

A snowflake postmark on a scalloped shield

Winter Postmark is a Christmas postmark ornament SVG with a snowflake, curved cancellation lines and the words MERRY MAIL. A lightly scalloped shield frames the engraved design.

76 × 94 mm outlineOne-piece plywood ornamentSVG + English guide + design map

Cancellation waves above MERRY MAIL

The upper snowflake gives the curved cancellation marks a point to start from. Two lines of outlined lettering bring the focus down the center of the shield. Fine scallops follow the outer cut and bring the character of a postage edge to the shape.

Leave a little room around the shield when you hang it near seasonal cards, or use it as an ornament on the outside of a wrapped parcel. Inspect the scallops at actual size before resizing.

Winter Postmark wooden Christmas ornament with MERRY MAIL lettering and a snowflake in a seasonal gift display.
Winter Postmark places a snowflake and cancellation waves above MERRY MAIL. Illustrative display. Digital files only.

Size, paths and hanging hole

Winter Postmark Christmas Ornament SVG specifications
Download ornament.svg, README.txt and design-map.png in a ZIP
Cut profile Vertical postage-style shield with a scalloped edge, 76 × 94 mm
SVG page 86 × 104 mm
Hanging hole One round 4 mm cut hole at the top
Cut paths Two closed red contours for the hanging hole and outer profile, with centered 0.025 mm strokes
Engraving Snowflake, curved cancellation lines and original outlined MERRY MAIL lettering
Material Uncoated plywood approved for the exact laser and operation. Nominal 3 mm plywood is a starting point if the stock is approved.
SKU VD-WP-ORN

The dimensions describe the vector geometry before kerf. Leave the clearance your machine requires and allow for the thickness of the cord.

From SVG to a hanging decoration

  1. Import and check scale

    Extract the ZIP and import ornament.svg at its supplied size. Test a scrap of the same approved plywood. Look closely at the scalloped edges in the cut preview and check that the cancellation lines are separate from the cutting operations.

  2. Assign cut and engraving

    Assign the black fills to engraving and the red paths to cutting. Where the controller supports it, engrave first, cut the hanging hole and release the outer profile last.

  3. Fit the hanging cord

    Once the piece has cooled, remove loose residue and test your chosen cord in the hole. Choose a cord that fits the finished diameter and supports the weight of your ornament.

The geometry was verified digitally. Make a physical test piece to check settings, engraving contrast and cord fit.

Prepare the file for your machine

Glowforge. Import the SVG in the app supported by your model. Compare the cut size with the dimensions above, assign black to Engrave and red to Cut, and preview the operation order.

xTool Studio or XCS. Use the software supported by your machine and check the SVG import DPI. Verify the resulting size in millimeters. Assign black fills to Engrave and the thin red outlines to Cut.

Epilog. Use Pulse SVG import on supported models and firmware. In a vector editor and Dashboard workflow, retain the centered 0.025 mm red strokes and check that the driver recognizes them as vectors. Route the black fills to engraving.

CO₂ or diode lasers. Use an SVG workflow such as LightBurn with equipment it supports. Verify the size and that the stock and its adhesive are suitable for your wavelength. Set red to a cutting Line layer and black to an engraving Fill layer. Follow your machine’s exhaust and supervision instructions and derive settings from a scrap sample.

Common questions

What comes with the digital download?

The ZIP contains ornament.svg, README.txt and design-map.png. Cut and engrave from the SVG. The English guide explains setup and the PNG shows the cut and engraving layout. The download contains digital files only.

Which details cut through on Winter Postmark?

The two red paths cut the 76 × 94 mm scalloped shield and its 4 mm hanging hole. The snowflake, cancellation lines and MERRY MAIL appear as engravings on the wood.

Can I use this SVG with my CO₂ or diode laser?

Use the SVG workflow supported by your controller and confirm that your plywood, including its adhesive and thickness, is approved for the machine. Verify the imported dimensions and test cutting and engraving on scrap of the same stock.

Can I resize the ornament or sell the ones I make?

Scale the profile, hole and engraved art together. Check that your cord fits and that there is enough wood between the hole and the outer edge. You may sell the finished ornaments you make. See the README for digital-file terms.

Winter Postmark Christmas Ornament SVG has received 0 reviews with an average rating of out of 5
Reviews are enabled for non customers for demo purposes