$1.20

Cocoa Clink Christmas Ornament SVG

0 reviews
  • Subtotal

    {{ currencyFormat( pricing_summary.total_amount ) }}

A holiday mug with two marshmallows

SIP THE SNOW below a star and curling steam

Cocoa Clink is a Christmas cocoa ornament SVG for a one-piece plywood mug. A four-point star sits between the rising steam curls, above two marshmallows and the original words SIP THE SNOW.

93 × 83 mm outlineOne-piece plywood ornamentSVG + English guide + design map

A rounded handle and two lines of type

The engraved handle curve follows the rounded lobe of the outer profile. SIP and THE SNOW are drawn outlines set in two rows. Above the lettering, the four-point star gives the steam curls a center.

Display the mug on a tree or tie it to a wrapped gift with a cocoa theme. Test the fine steam curls at actual size to see how the engraving reads on your plywood.

Cocoa Clink wooden mug ornament with SIP THE SNOW lettering, a star and marshmallows in a holiday cocoa display.
Cocoa Clink places a small star between two curls of steam above SIP THE SNOW. Illustrative display. Digital files only.

Size, paths and hanging hole

Cocoa Clink Christmas Ornament SVG specifications
Download ornament.svg, README.txt and design-map.png in a ZIP
Cut profile Rounded mug silhouette with a solid handle lobe on the right, 93 × 83 mm
SVG page 103 × 93 mm
Hanging hole One round 4 mm cut hole at the top
Cut paths Two closed red contours for the hanging hole and outer profile, with centered 0.025 mm strokes
Engraving Steam curls, four-point star, two marshmallows, handle curve and original outlined SIP THE SNOW lettering
Material Uncoated plywood approved for the exact laser and operation. Nominal 3 mm plywood is a starting point if the stock is approved.
SKU VD-CK-ORN

The dimensions describe the vector geometry before kerf. Leave the clearance your machine requires and allow for the thickness of the cord.

From SVG to a hanging decoration

  1. Import and check scale

    Extract the ZIP and import ornament.svg at its supplied size. Test a scrap of the same approved plywood. Check that the four-point star, small steam curls and handle curve are set to engraving. The only inner through-cut is the hanging hole.

  2. Assign cut and engraving

    Assign the black fills to engraving and the red paths to cutting. Where the controller supports it, engrave first, cut the hanging hole and release the outer profile last.

  3. Fit the hanging cord

    Once the piece has cooled, remove loose residue and test your chosen cord in the hole. Choose a cord that fits the finished diameter and supports the weight of your ornament.

The geometry was verified digitally. Make a physical test piece to check settings, engraving contrast and cord fit.

Prepare the file for your machine

Glowforge. Import the SVG in the app supported by your model. Compare the cut size with the dimensions above, assign black to Engrave and red to Cut, and preview the operation order.

xTool Studio or XCS. Use the software supported by your machine and check the SVG import DPI. Verify the resulting size in millimeters. Assign black fills to Engrave and the thin red outlines to Cut.

Epilog. Use Pulse SVG import on supported models and firmware. In a vector editor and Dashboard workflow, retain the centered 0.025 mm red strokes and check that the driver recognizes them as vectors. Route the black fills to engraving.

CO₂ or diode lasers. Use an SVG workflow such as LightBurn with equipment it supports. Verify the size and that the stock and its adhesive are suitable for your wavelength. Set red to a cutting Line layer and black to an engraving Fill layer. Follow your machine’s exhaust and supervision instructions and derive settings from a scrap sample.

Common questions

What comes with the digital download?

The ZIP contains ornament.svg, README.txt and design-map.png. Cut and engrave from the SVG. The English guide explains setup and the PNG shows the cut and engraving layout. The download contains digital files only.

Is the mug handle a through-cut opening?

The right handle lobe stays solid and its curve engraves on the face. The red paths cut the 93 × 83 mm mug outline and the nominal 4 mm hanging hole. The SVG page is 103 × 93 mm.

Can I use this SVG with my CO₂ or diode laser?

Use the SVG workflow supported by your controller and confirm that your plywood, including its adhesive and thickness, is approved for the machine. Verify the imported dimensions and test cutting and engraving on scrap of the same stock.

Can I resize the ornament or sell the ones I make?

Scale the profile, hole and engraved art together. Check that your cord fits and that there is enough wood between the hole and the outer edge. You may sell the finished ornaments you make. See the README for digital-file terms.

Cocoa Clink Christmas Ornament SVG has received 0 reviews with an average rating of out of 5
Reviews are enabled for non customers for demo purposes