Winter crossings
A lantern at the snowy crossing
Lantern Bridge is a Christmas bridge shadow box SVG with a small arched footbridge across a winter stream. A lantern and pine-lined banks frame the crossing, while separate wood layers give the scene depth.
An arch between snowy banks
The curve of the footbridge draws the eye across the stream. The upright lantern sets the scale near the bank, and the pines lead the eye deeper into the scene. Add depth through stock tone or finish. Cut the four panels first so you can compare them in their final order.
The ZIP contains digital files. Supply your own wood, finish, adhesive and display hardware.

Sizes and layer order
| Download | 01-front.svg, 02-middle.svg, 03-background.svg, 04-backing.svg, README.txt and assembly-map.png in a ZIP |
|---|---|
| Finished footprint | 120 × 120 mm per layer |
| SVG page size | 130 × 130 mm per SVG |
| Front to back | 01 footbridge and lantern, 02 fir bank and stream ripples, 03 distant ridge with four firs, 04 engraved winter sky on a solid backing. |
| Red cut paths | Closed 0.025 mm centerline strokes for the outer profiles and any interior openings |
| Black engraving | Bridge rail, lantern and stream ripples, plus snow dots and two glints on the backing. |
| Stock | Uncoated plywood approved for the exact laser and operations. Nominal 3 mm plywood gives an approximately 12 mm bare stack before adhesive or finish. |
| SKU | VD-LB-SBX |
Dimensions describe the vector geometry before kerf. The thickness of the assembled piece depends on the stock and adhesive you use.
Cut and assemble the scene
-
Import and check scale
Extract the ZIP. Open each numbered SVG at the supplied size and compare its outer profile with the millimeter dimensions above before machining. Keep the bridge supports and slender lantern elements attached to their respective panels. Check small details on the imported layer before cutting.
-
Assign the cuts and engraving
Set red to through-cutting and any black fills to engraving. Where the software supports the order, run engraving first, cut the interior openings next, then release the outer profiles. Use a test coupon from the same stock to check engraving, kerf and the smallest opening before machining the panels.
-
Dry fit and assemble
Align the outer edges and dry fit all four layers. Add suitable adhesive at the contact areas after machining. Keep the stack flat during curing. Set the lantern and bridge layers over the pine banks and backing in the numbered order. Align the outside edges before applying adhesive.
The geometry was verified digitally. Make a physical prototype to check cut quality, layer fit and the final display method before producing multiples.
Prepare the SVGs for your machine
Glowforge. Upload each SVG in the Glowforge app. Confirm the 120 mm cut profile, assign red to Cut and any black fills to Engrave, then check the operation order before starting. Glowforge SVG upload · Glowforge operation order
xTool Studio or XCS. Use the software your model supports. Compare each imported cut profile with the 120 mm specification and check the SVG import DPI if the size differs. Assign red vectors to Cut and any black fills to Engrave. xTool vector import guide
Epilog. Import the SVGs into Pulse on supported models and firmware. If you use a supported vector editor and Dashboard, retain the centered 0.025 mm red strokes and confirm that the driver recognizes them as vector cuts. Route any black fills to engraving. Epilog Pulse setup guide · Epilog Dashboard vector jobs
CO₂ or diode lasers. Use the SVG workflow supported by your controller. In LightBurn, assign red to a cutting Line layer and any black fills to an engraving Fill layer. Confirm that your machine supports both the wood and the adhesive used to make the plywood. Establish settings with a test coupon and follow your manufacturer’s exhaust and supervision instructions. LightBurn SVG import
Common questions
What comes with the digital download?
The ZIP contains 01-front.svg, 02-middle.svg, 03-background.svg, 04-backing.svg, README.txt and assembly-map.png. Cut from the SVGs and check the order on the map. Supply stock, adhesive and any display hardware.
How do I keep the bridge and banks aligned?
The four panels share a 120 × 120 mm cut footprint. Dry fit the backing and scene layers against a square reference edge, then check the crossing from the front before adding adhesive.
Can I use the files with a CO₂ or diode laser?
Use the SVG workflow your controller supports and stock approved for your laser. Match the outer dimensions across layers. Test cutting, engraving and fit on matching scrap.
Can I resize the project or sell the scenes I make?
Scale all layers together. Check small details, connector widths and fit again. You may sell finished pieces you make. See the README for the digital file terms.