$1.20

Firlight Choir Christmas Shadow Box SVG

0 reviews
  • Subtotal

    {{ currencyFormat( pricing_summary.total_amount ) }}

An outdoor carol

Three carolers beneath a fir

Firlight Choir is a Christmas carolers shadow box SVG with three bundled singers on the front of a layered winter scene. Original coat and hat shapes distinguish the figures around their songbooks.

120 × 120 mm per layerFour stacked layersSVG + English guide + assembly map

A small choir on the lower terrace

Three figures hold open books above the terrace, with engraved details distinguishing their winter clothes. A tall fir behind the choir carries two engraved garland curves. The numbered layers share a square edge for dry fitting.

The ZIP contains digital files. Supply your own wood, finish, adhesive and display hardware.

Firlight Choir layered wood scene displayed upright, with three winter carolers holding engraved songbooks beneath a fir.
Three carolers stand across the foreground terrace with a tall fir behind them. Illustrative display. Digital files only.

Sizes and layer order

Firlight Choir Christmas Shadow Box SVG specifications
Download 01-front.svg, 02-middle.svg, 03-background.svg, 04-backing.svg, README.txt and assembly-map.png in a ZIP
Finished footprint 120 × 120 mm per layer
SVG page size 130 × 130 mm per SVG
Front to back 01 bundled carolers, 02 tall fir and hillside, 03 snowy grove, 04 winter sky on a solid backing.
Red cut paths Closed 0.025 mm centerline strokes for the outer profiles and any interior openings
Black engraving Open songbooks and clothing marks on the carolers, with additional winter accents shown on the layer maps.
Stock Uncoated plywood approved for the exact laser and operations. Nominal 3 mm plywood gives an approximately 12 mm bare stack before adhesive or finish.
SKU VD-FC-SBX

Dimensions describe the vector geometry before kerf. The thickness of the assembled piece depends on the stock and adhesive you use.

Cut and assemble the scene

  1. Import and check scale

    Extract the ZIP. Open each numbered SVG at the supplied size and compare its outer profile with the millimeter dimensions above before machining. Keep narrow details on the choir panel intact when removing the surrounding scrap. Check the figure and songbook details in your machine's preview.

  2. Assign the cuts and engraving

    Set red to through-cutting and any black fills to engraving. Where the software supports the order, run engraving first, cut the interior openings next, then release the outer profiles. Use a test coupon from the same stock to check engraving, kerf and the smallest opening before machining the panels.

  3. Dry fit and assemble

    Align the outer edges and dry fit all four layers. Add suitable adhesive at the contact areas after machining. Keep the stack flat during curing. Set the choir panel over the inner scene and sight along its top edge. Confirm all three singers are visible before bonding the panels.

The geometry was verified digitally. Make a physical prototype to check cut quality, layer fit and the final display method before producing multiples.

Prepare the SVGs for your machine

Glowforge. Upload each SVG in the Glowforge app. Confirm the 120 mm cut profile, assign red to Cut and any black fills to Engrave, then check the operation order before starting. Glowforge SVG upload · Glowforge operation order

xTool Studio or XCS. Use the software your model supports. Compare each imported cut profile with the 120 mm specification and check the SVG import DPI if the size differs. Assign red vectors to Cut and any black fills to Engrave. xTool vector import guide

Epilog. Import the SVGs into Pulse on supported models and firmware. If you use a supported vector editor and Dashboard, retain the centered 0.025 mm red strokes and confirm that the driver recognizes them as vector cuts. Route any black fills to engraving. Epilog Pulse setup guide · Epilog Dashboard vector jobs

CO₂ or diode lasers. Use the SVG workflow supported by your controller. In LightBurn, assign red to a cutting Line layer and any black fills to an engraving Fill layer. Confirm that your machine supports both the wood and the adhesive used to make the plywood. Establish settings with a test coupon and follow your manufacturer’s exhaust and supervision instructions. LightBurn SVG import

Common questions

What comes with the digital download?

The ZIP contains 01-front.svg, 02-middle.svg, 03-background.svg, 04-backing.svg, README.txt and assembly-map.png. Cut from the SVGs and check the order on the map. Supply stock, adhesive and any display hardware.

How do the figures stay together?

The three carolers are connected to the foreground panel. Keep the figures attached to the terrace during cleanup, and use the layer map to position them in front of the other panels.

Can I use the files with a CO₂ or diode laser?

Use the SVG workflow your controller supports and stock approved for your laser. Match the outer dimensions across layers. Test cutting, engraving and fit on matching scrap.

Can I resize the project or sell the scenes I make?

Scale all layers together. Check small details, connector widths and fit again. You may sell finished pieces you make. See the README for the digital file terms.

Firlight Choir Christmas Shadow Box SVG has received 0 reviews with an average rating of out of 5
Reviews are enabled for non customers for demo purposes