At the hearth
Stockings along a winter mantel
Fireside Stockings is a Christmas fireplace shadow box SVG with three different stockings across the mantel. The arched opening below reveals a flame and engraved logs.
Depth inside the fireplace
The stockings have different directions and engraved motifs along the front of the mantel. The hearth opening reveals the recessed flame and logs. Short lines on the surround suggest masonry joints and frame the opening.
The ZIP contains digital files. Supply your own wood, finish, adhesive and display hardware.

Sizes and layer order
| Download | 01-front.svg, 02-middle.svg, 03-background.svg, 04-backing.svg, README.txt and assembly-map.png in a ZIP |
|---|---|
| Finished footprint | 120 × 120 mm per layer |
| SVG page size | 130 × 130 mm per SVG |
| Front to back | 01 mantelshelf and three stockings, 02 arched fireplace surround, 03 flame and engraved logs, 04 festive sprig and sparks on a solid backing. |
| Red cut paths | Closed 0.025 mm centerline strokes for the outer profiles and any interior openings |
| Black engraving | Stocking accents, log and ember marks, and a seasonal sprig and sparks. |
| Stock | Uncoated plywood approved for the exact laser and operations. Nominal 3 mm plywood gives an approximately 12 mm bare stack before adhesive or finish. |
| SKU | VD-FS-SBX |
Dimensions describe the vector geometry before kerf. The thickness of the assembled piece depends on the stock and adhesive you use.
Cut and assemble the scene
-
Import and check scale
Extract the ZIP. Open each numbered SVG at the supplied size and compare its outer profile with the millimeter dimensions above before machining. Check the fabric marks and log lines on matching scrap. Keep the stockings joined to the mantel and run the hearth opening before the perimeter.
-
Assign the cuts and engraving
Set red to through-cutting and any black fills to engraving. Where the software supports the order, run engraving first, cut the interior openings next, then release the outer profiles. Use a test coupon from the same stock to check engraving, kerf and the smallest opening before machining the panels.
-
Dry fit and assemble
Align the outer edges and dry fit all four layers. Add suitable adhesive at the contact areas after machining. Keep the stack flat during curing. Hold the mantel layer above the recessed hearth and check that the logs are visible below the stockings before applying adhesive.
The geometry was verified digitally. Make a physical prototype to check cut quality, layer fit and the final display method before producing multiples.
Prepare the SVGs for your machine
Glowforge. Upload each SVG in the Glowforge app. Confirm the 120 mm cut profile, assign red to Cut and any black fills to Engrave, then check the operation order. If both cuts appear in one step, make a working copy with a different stroke color for the perimeter. Assign that color to Cut and place it last. Glowforge SVG upload · Glowforge operation order
xTool Studio or XCS. Use the software your model supports. Compare each imported cut profile with the 120 mm specification and check the SVG import DPI if the size differs. Assign red vectors to Cut and any black fills to Engrave. xTool vector import guide
Epilog. Import the SVGs into Pulse on supported models and firmware. If you use a supported vector editor and Dashboard, retain the centered 0.025 mm red strokes and confirm that the driver recognizes them as vector cuts. Route any black fills to engraving. Epilog Pulse setup guide · Epilog Dashboard vector jobs
CO₂ or diode lasers. Use the SVG workflow supported by your controller. In LightBurn, assign red to a cutting Line layer and any black fills to an engraving Fill layer. Confirm that your machine supports both the wood and the adhesive used to make the plywood. Establish settings with a test coupon and follow your manufacturer’s exhaust and supervision instructions. LightBurn SVG import
Common questions
What comes with the digital download?
The ZIP contains 01-front.svg, 02-middle.svg, 03-background.svg, 04-backing.svg, README.txt and assembly-map.png. Cut from the SVGs and check the order on the map. Supply stock, adhesive and any display hardware.
How do I make the logs inside the hearth?
The log marks are surface engravings. Assign them to Engrave, clear the hearth opening in the appropriate panel, and dry fit the cut layers to check that the marks remain visible from the front.
Can I use the files with a CO₂ or diode laser?
Use the SVG workflow your controller supports and stock approved for your laser. Match the outer dimensions across layers. Test cutting, engraving and fit on matching scrap.
Can I resize the project or sell the scenes I make?
Scale all layers together. Check small details, connector widths and fit again. You may sell finished pieces you make. See the README for the digital file terms.