Easter morning
First light at the open tomb
First Light is a Christian empty tomb shadow box SVG with an arched rock entrance and a round stone moved to the left. An engraved sunrise gives the layered scene its Easter morning setting.
A round stone beside an open arch
The moved stone rests on the curved foreground slope. The tomb sits farther back to the right, where a cut arch reveals a recessed dark arch near the floor. The sunrise is engraved on the solid backing to the left.
The ZIP contains digital files. Supply your own wood, finish, adhesive and display hardware.

Sizes and layer order
| Download | 01-front.svg, 02-middle.svg, 03-background.svg, 04-backing.svg, README.txt and assembly-map.png in a ZIP |
|---|---|
| Finished footprint | 120 × 120 mm per layer |
| SVG page size | 130 × 130 mm per SVG |
| Front to back | 01 curved slope and moved stone, 02 rock tomb and cut entrance, 03 rocky terrain, 04 engraved sunrise on a solid backing. |
| Red cut paths | Closed 0.025 mm centerline strokes for the outer profiles and any interior openings |
| Black engraving | Sunrise on the solid backing and the surface accents shown in the assembly map. |
| Stock | Uncoated plywood approved for the exact laser and operations. Nominal 3 mm plywood gives an approximately 12 mm bare stack before adhesive or finish. |
| SKU | VD-FLET-SBX |
Dimensions describe the vector geometry before kerf. The thickness of the assembled piece depends on the stock and adhesive you use.
Cut and assemble the scene
-
Import and check scale
Extract the ZIP. Open each numbered SVG at the supplied size and compare its outer profile with the millimeter dimensions above before machining. Check that the arched entrance appears as an interior cut. Keep the round stone supported by its foreground slope while clearing the surrounding scrap.
-
Assign the cuts and engraving
Set red to through-cutting and any black fills to engraving. Where the software supports the order, run engraving first, cut the interior openings next, then release the outer profiles. Use a test coupon from the same stock to check engraving, kerf and the smallest opening before machining the panels.
-
Dry fit and assemble
Align the outer edges and dry fit all four layers. Add suitable adhesive at the contact areas after machining. Keep the stack flat during curing. Stack the rocky terrain behind the tomb opening. View the panels from the front to confirm the arch stays clear and the sunrise reads above the scene before bonding.
The geometry was verified digitally. Make a physical prototype to check cut quality, layer fit and the final display method before producing multiples.
Prepare the SVGs for your machine
Glowforge. Upload each SVG in the Glowforge app. Confirm the 120 mm cut profile, assign red to Cut and any black fills to Engrave, then check the operation order. If both cuts appear in one step, make a working copy with a different stroke color for the perimeter. Assign that color to Cut and place it last. Glowforge SVG upload · Glowforge operation order
xTool Studio or XCS. Use the software your model supports. Compare each imported cut profile with the 120 mm specification and check the SVG import DPI if the size differs. Assign red vectors to Cut and any black fills to Engrave. xTool vector import guide
Epilog. Import the SVGs into Pulse on supported models and firmware. If you use a supported vector editor and Dashboard, retain the centered 0.025 mm red strokes and confirm that the driver recognizes them as vector cuts. Route any black fills to engraving. Epilog Pulse setup guide · Epilog Dashboard vector jobs
CO₂ or diode lasers. Use the SVG workflow supported by your controller. In LightBurn, assign red to a cutting Line layer and any black fills to an engraving Fill layer. Confirm that your machine supports both the wood and the adhesive used to make the plywood. Establish settings with a test coupon and follow your manufacturer’s exhaust and supervision instructions. LightBurn SVG import · LightBurn cut modes
Common questions
What comes with the digital download?
The ZIP contains 01-front.svg, 02-middle.svg, 03-background.svg, 04-backing.svg, README.txt and assembly-map.png. Cut from the SVGs and check the order on the map. Supply stock, adhesive and any display hardware.
How is the depth inside the tomb made?
An arched opening is cut through the middle tomb layer. The rocky background sits behind it. Dry fit those two panels to confirm the opening and rock relief are visible before gluing the full stack.
Can I use the files with a CO₂ or diode laser?
Use the SVG workflow your controller supports and stock approved for your laser. Match the outer dimensions across layers. Test cutting, engraving and fit on matching scrap.
Can I resize the project or sell the scenes I make?
Scale all layers together. Check small details, connector widths and fit again. You may sell finished pieces you make. See the README for the digital file terms.