Wrapped parcels in front of a fir
TIED IN JOY beneath the Christmas tree
Evergreen Parcel is a Christmas gift layered art SVG for a four-layer wooden panel. Wrapped gifts sit in front of a three-tier fir. The words TIED IN JOY are outlined as engraving on the main parcel.
Two lines of lettering on the closest parcel
TIED and IN JOY occupy two lines on the front parcel. The stacked fir branches rise behind the gifts, while a low hillside and winter greenery give the opening another plane. Snow marks sit on the solid back.
The ZIP contains digital files. Supply your own wood, finish, adhesive and display hardware.

Sizes and layer order
| Download | 01-front.svg, 02-middle.svg, 03-background.svg, 04-backing.svg, README.txt and assembly-map.png in a ZIP |
|---|---|
| Finished footprint | 120 × 120 mm per layer |
| SVG page size | 130 × 130 mm per SVG |
| Front to back | Wrapped parcels with TIED IN JOY → three-tier fir → hillside and winter greenery → solid backing with snow marks |
| Red cut paths | Closed 0.025 mm centerline strokes for the outer profiles and any interior openings |
| Black engraving | Black filled decorative marks and original outlined TIED IN JOY lettering on the main parcel |
| Stock | Uncoated plywood approved for the exact laser and operations. Nominal 3 mm plywood gives an approximately 12 mm bare stack before adhesive or finish. |
| SKU | VD-EP-LAY |
Dimensions describe the vector geometry before kerf. The thickness of the assembled piece depends on the stock and adhesive you use.
Cut and assemble the scene
-
Import and check scale
Extract the ZIP. Open each numbered SVG at the supplied size and compare its outer profile with the millimeter dimensions above before machining. Check the lettering as an engraving and test it at actual size. Keep the parcel and fir layers upright so the wording and tree align when stacked.
-
Assign the cuts and engraving
Set red to through-cutting and any black fills to engraving. Where the software supports the order, run engraving first, cut the interior openings next, then release the outer profiles. Check the planned operations on scrap first.
-
Dry fit and assemble
Align the outer edges and dry fit all four layers. Add suitable adhesive at the contact areas after machining. Keep the stack flat during curing. Check the top of each layer against the assembly map so the letters on the parcel stay upright. Dry fit until the three evergreen tiers show clearly behind it. Fit any display support after the adhesive cures.
The geometry was verified digitally. Make a physical prototype to check cut quality, layer fit and the final display method before producing multiples.
Prepare the SVGs for your machine
Glowforge. Import each SVG in the app supported by your model. Verify the size, set red to Cut and black fills to Engrave where present, and preview the operation order.
xTool Studio or XCS. Use the software your machine supports and check the SVG import DPI. Verify the size in millimeters for each numbered layer. Assign red vectors to Cut and any black fills to Engrave.
Epilog. Use Pulse SVG import on supported models and firmware. In a vector editor and Dashboard workflow, retain centered 0.025 mm red strokes and confirm that they register as vectors. Route any black fills to engraving.
CO₂ or diode lasers. Use an SVG workflow such as LightBurn with equipment it supports. Assign red to a cutting Line layer and any black fills to an engraving Fill layer. Confirm that the stock and any glue in the plywood suit the wavelength and equipment. Use matching scrap to establish settings and follow your manufacturer’s exhaust and supervision instructions.
Common questions
What comes with the digital download?
The ZIP contains 01-front.svg, 02-middle.svg, 03-background.svg, 04-backing.svg, README.txt and assembly-map.png. Cut from the SVGs and check the order on the map. Supply stock, adhesive and any display hardware.
Do I need a font for the words TIED IN JOY?
The words are already outlined in the front SVG as filled engraving shapes. They are arranged in two lines on the main parcel. Import the file at its supplied size and test the smaller IN JOY line on scrap.
Can I use the files with a CO₂ or diode laser?
Use the SVG workflow your controller supports and stock approved for your laser. Match the outer dimensions across layers. Test cutting, engraving and fit on matching scrap.
Can I resize the project or sell the scenes I make?
Scale all layers together. Check small details, connector widths and fit again. You may sell finished pieces you make. See the README for the digital file terms.