Praise in everyday life
Praise in the Ordinary
Ordinary Praise is a Christian lettering SVG with PRAISE cut as standing letter shapes joined to an integral lower band. The original words IN THE ORDINARY engrave across that band.
Cut letters above an engraved band
The large PRAISE silhouette and the quieter words below use separate operations. The letters stay connected through the solid lower band. Display the finished profile in a holder you provide.
The ZIP contains digital files. Supply your own wood, finish and display hardware.

Size and operations
| Download | design.svg, README.txt and design-map.png in a ZIP |
|---|---|
| Cut footprint | 180 × 105 mm |
| SVG page | 190 × 115 mm |
| Profile | One-piece PRAISE silhouette with an integrated lower band |
| Display mounting | Choose your own display holder sized to the finished stock. The integral band supports the letters. |
| Red cut paths | Six closed paths with centered 0.025 mm strokes. One outer silhouette, three letter counters and two openings bordered by the lower band. |
| Black engraving | Original IN THE ORDINARY lettering and the surface details shown on the design map. |
| Stock | Use uncoated plywood approved for the exact laser and operation. Use nominal 3 mm stock where your machine and the material allow it. |
| SKU | VD-OPR-LET |
Dimensions refer to the vector geometry before kerf. Keep any required clearance around the profile on your usable laser bed.
From the SVG to the finished sign
-
Import and confirm size
Extract the ZIP and open design.svg at its supplied scale. Confirm an outline 180 mm wide. Keep the lower band attached to every letter and check the inner letter openings in your cut preview.
-
Assign the operations
Assign red centerlines to through-cutting and black filled shapes to engraving. Engrave first, cut any interior openings next and release the outer profile last when your software supports that order. Test kerf, detail and cut depth on a coupon from the same stock.
-
Check the display fit
Fit the lower band into a holder that suits the measured stock and leaves the engraved line visible. Check balance with a complete prototype.
The vector geometry was checked digitally. Cut a physical prototype to confirm your settings, the small details and the display fit before producing multiples.
Prepare the file for your machine
Glowforge. Upload the SVG and confirm its outline size. Assign red to Cut and black fills to Engrave. If interior and perimeter cuts appear in one step, give the perimeter a separate stroke color in a working copy and place that Cut step last. Glowforge SVG upload · Glowforge operation order
xTool Studio or XCS. Use the software supported by your model. Confirm the outline in millimeters and check the SVG import DPI if the size differs. Set red vectors to Cut and black fills to Engrave. xTool vector import guide
Epilog. Open the SVG with Pulse on supported models and firmware. In a supported vector editor and Dashboard workflow, retain the centered 0.025 mm cut strokes and confirm that the driver reads them as vector cuts. Route the black fills to engraving. Epilog Pulse setup guide · Epilog Dashboard vector jobs
CO₂ or diode lasers. Use software that supports SVG and your controller. In LightBurn, use Line mode for cutting and Fill mode for engraving. Verify your machine supports the plywood and its adhesive, test on matching stock and follow the manufacturer’s exhaust and supervision instructions. LightBurn SVG import · LightBurn cut modes
Common questions
What comes with the digital download?
The ZIP contains design.svg, README.txt and design-map.png. Process the SVG and use the guide and design map to check the operation assignments. Supply your own wood and display hardware.
Is PRAISE engraved or cut out?
PRAISE forms the cut silhouette. The three letter counters and the two enclosed openings bordered by the lower band are also through-cut. IN THE ORDINARY uses black vector engraving on the band.
Can I use this SVG with a CO₂ or diode laser?
Use SVG-capable software that supports your controller. Check the plywood's thickness and adhesive against your machine's material guidance. Compare the profile with your usable bed and test the cut and engraving on matching scrap.
Can I resize the design or sell finished pieces?
Scale all vectors together. Recheck detail size, any mounting clearance and the strength of the narrowest connections. You may sell finished physical pieces you make. See the README for the digital file terms.