A quiet depot in a snowy landscape
A snow-covered depot and a small train
Snowbound Station is a Christmas station shadow box SVG for building a winter railway scene. A snow-covered depot on the right anchors the foreground. The smaller train sits to the left in the middle layer, with pine ridges behind it.
The depot sets the scale of the scene
The station roof holds the main area of snow in the front layer. The small train sits slightly farther back so it reads as part of the setting. Its wheels are engraved on the wood. The rear pine ridges and snow marks keep the landscape visible around the depot.
The ZIP contains digital files. Supply your own wood, finish, adhesive and display hardware.

Sizes and layer order
| Download | 01-front.svg, 02-middle.svg, 03-background.svg, 04-backing.svg, README.txt and assembly-map.png in a ZIP |
|---|---|
| Finished footprint | 120 × 120 mm per layer |
| SVG page size | 130 × 130 mm per SVG |
| Front to back | Snow-covered depot and snowbank → small train → pine ridges → solid backing with engraved snow |
| Red cut paths | Closed 0.025 mm centerline strokes for the outer profiles and any interior openings |
| Black engraving | Black filled surface marks including the train wheels and falling snow |
| Stock | Uncoated plywood approved for the exact laser and operations. Nominal 3 mm plywood gives an approximately 12 mm bare stack before adhesive or finish. |
| SKU | VD-SS-SBX |
Dimensions describe the vector geometry before kerf. The thickness of the assembled piece depends on the stock and adhesive you use.
Cut and assemble the scene
-
Import and check scale
Extract the ZIP. Open each numbered SVG at the supplied size and compare its outer profile with the millimeter dimensions above before machining. Preview the wheels as engraving on the train. Lay the depot layer over the middle layer to check that the train is visible at the left before fixing the stack.
-
Assign the cuts and engraving
Set red to through-cutting and any black fills to engraving. Where the software supports the order, run engraving first, cut the interior openings next, then release the outer profiles. Check the planned operations on scrap first.
-
Dry fit and assemble
Align the outer edges and dry fit all four layers. Add suitable adhesive at the contact areas after machining. Keep the stack flat during curing. Keep the depot in front of the train and the pine ridges behind both. Check that the left and right sides of the scene read clearly before adding adhesive. Measure the completed depth against any stand or frame.
The geometry was verified digitally. Make a physical prototype to check cut quality, layer fit and the final display method before producing multiples.
Prepare the SVGs for your machine
Glowforge. Import each SVG in the app supported by your model. Verify the size, set red to Cut and black fills to Engrave where present, and preview the operation order.
xTool Studio or XCS. Use the software your machine supports and check the SVG import DPI. Verify the size in millimeters for each numbered layer. Assign red vectors to Cut and any black fills to Engrave.
Epilog. Use Pulse SVG import on supported models and firmware. In a vector editor and Dashboard workflow, retain centered 0.025 mm red strokes and confirm that they register as vectors. Route any black fills to engraving.
CO₂ or diode lasers. Use an SVG workflow such as LightBurn with equipment it supports. Assign red to a cutting Line layer and any black fills to an engraving Fill layer. Confirm that the stock and any glue in the plywood suit the wavelength and equipment. Use matching scrap to establish settings and follow your manufacturer’s exhaust and supervision instructions.
Common questions
What comes with the digital download?
The ZIP contains 01-front.svg, 02-middle.svg, 03-background.svg, 04-backing.svg, README.txt and assembly-map.png. Cut from the SVGs and check the order on the map. Supply stock, adhesive and any display hardware.
Are the small train wheels separate pieces?
The wheels are engraved details on the middle layer. The depot is in front, with the pine ridges and snow farther back. Each of the four layers has a 120 × 120 mm outer profile.
Can I use the files with a CO₂ or diode laser?
Use the SVG workflow your controller supports and stock approved for your laser. Match the outer dimensions across layers. Test cutting, engraving and fit on matching scrap.
Can I resize the project or sell the scenes I make?
Scale all layers together. Check small details, connector widths and fit again. You may sell finished pieces you make. See the README for the digital file terms.